For buyers, R&D and quality teams, the grade is not a late purchasing note: it sets shrinkage, gate layout, drying and whether pocket and ring dimensions are checked dry-as-molded, after conditioning, or both. This guide is the PA66 follow-on to our materials and structure article. It does not repeat that structure map, and it does not rate cage life or speed.
Dongying (Suzhou Dongying Electronic Technology Co., Ltd.) builds precision molds and molds bearing cage components in Suzhou, China. Documented catalog examples include a deep-groove ball cage listed as PA66+30%GF and a needle-roller cage listed as PA66+15%GF. Those cells describe those parts; they are not a default grade list. Tolerances and acceptance criteria are reviewed against your drawings.
Why buyers specify a PA66 bearing cage
Short answer: bearing manufacturers injection-mold PA66 because it combines strength with elasticity and can form pocket shapes that stamped metal cages cannot form as freely.
SKF describes polyamide 66, with or without glass fibers, as the most commonly used material for injection-molded cages, and as having a useful mix of strength and elasticity (SKF, Cages). An SKF engineering article adds the manufacturing reason: injection molding lets the pocket be shaped for rolling-element guidance and lubricant films, instead of accepting the sharper edges of a stamped steel window (SKF Evolution). Schaeffler likewise uses glass-fiber-reinforced polyamide cages in series bearings; in its double-row angular-contact information those cages carry the suffix TVH (Schaeffler, TPI 213).
For a custom cage the same reasons and the same limits apply. PA66 is a sound starting family when the cage must flex during assembly or running and stay within a temperature and lubricant range that polyamide can age in. It is the wrong family when moisture-driven size change is unacceptable, or when the oil or grease would age the polymer faster than the application can accept. Those calls belong to the named grade datasheet and your validation plan, not to a generic “nylon cage” line on a quotation request.
Moisture changes size and stiffness
Short answer: PA66 keeps absorbing moisture after it leaves the mold, so size and stiffness shift as the part equilibrates, and the drawing must say whether inspection is dry-as-molded, conditioned, or both.
Ensinger notes PA66’s rigidity, wear behavior and impact properties, and warns that the polymer absorbs moisture in a way that can change dimensional stability (Ensinger, TECAMID 66). That is why polyamide test methods treat moisture as part of the result. ISO 1110 exists because many polyamide properties depend on water content, and it defines an accelerated conditioning path whose equilibrium is close to 23 °C and 50 % relative humidity (ISO 1110:2019). Glass-filled grades usually take up less water than the same unfilled polymer, because glass itself does not absorb moisture, but they still move. Confirm the equilibrium value on the grade datasheet rather than copying a number from another product form.
| Inspection state | What it reflects | When teams use it |
|---|---|---|
| Dry-as-molded | The part as it left the tool, before service humidity | Process feedback and early dimensional checks |
| Conditioned | Size and stiffness closer to equilibrated use | Pocket fit, ring roundness and assembly feel in service |
| Both | The difference between the two states | Critical pocket, bridge and guiding diameters |
If the cage later runs in hot water, glycol or another aqueous fluid, ask the resin supplier about hydrolysis for that grade. SKF notes that polymer cage ageing is driven by temperature, time and the medium—the lubricant—around the cage (SKF, Cages). Do not treat a catalog PA66 example as approved for every fluid.
Glass fiber: stiffness versus flow direction
Short answer: glass fiber raises stiffness and heat capability, but fibers align with flow, so shrinkage and strength become directional and weld lines on thin pocket bridges need a planned gate.
Unfilled PA66 is sometimes chosen when toughness or snap-through assembly matters more than extra stiffness. Glass-filled PA66 (PA66-GF) is the more common cage discussion when bridges are thin and the ring must stay round. BASF notes that PA66 generally offers higher stiffness, strength and heat resistance than PA6, so a drawing that only says “nylon” is not finished (BASF Ultramid). The glass content is a second decision: documented examples on this site use different fill levels on different parts.
Fiber orientation has three tooling consequences. Shrinkage parallel to flow differs from shrinkage across flow, so a late switch from unfilled PA66 to a filled grade—or between fill levels—can force cavity steel rework on pockets. Weld lines form where flow fronts meet, often on a thin bridge that is also a loaded section. Gate vestiges and ejector pins should sit off the surfaces that guide or retain the rolling elements. Freeze the named grade, including glass content, before cavity steel is cut.
Heat, lubricant and when another family is better
Short answer: whether PA66 is suitable depends on operating temperature, exposure time and the lubricant; some applications outgrow it and move to PPS, POM or a metal cage.
SKF states that polymer cage properties are temperature-dependent and subject to ageing, and that suitability depends on the operating conditions and the life the bearing needs (SKF, Cages). Schaeffler’s TPI 213 text for double-row angular contact ball bearings says cages of glass-fiber-reinforced polyamide are suitable for operating temperatures up to +120 °C, limited by the cage material (Schaeffler, TPI 213). That figure is Schaeffler’s published guidance for those bearings, not a temperature rating for a cage molded to another drawing.
If the lubricant, continuous temperature or chemical exposure sits outside what the named PA66 grade can support, look at another family. This site documents a PPS tubular ball-cage design when a stiffer, lower-moisture polymer is the design material, and a slewing-segment example listed as POM. PEEK is not a standard quoted cage material here; only a customer-specified PEEK grade can be evaluated against your drawing.
| Topic | Unfilled PA66 | PA66-GF | PPS, when specified | POM, when specified |
|---|---|---|---|---|
| Moisture movement | Higher | Lower than unfilled, still present | Typically low | Typically low |
| Stiffness and heat | Moderate | Higher, and directional with flow | Often chosen when low moisture and higher heat are needed | Sliding behavior; confirm temperature on the datasheet |
| Molding watch-outs | Packing of thick-to-thin sections | Weld lines on bridges; anisotropic shrink | Process temperature; weld lines on filled grades | Sink where thick hubs meet thin bars |
| Site examples | Named on a drawing when required | Catalog examples at different glass contents | PPS tubular design page | Slewing-segment catalog example |
Trends only. Compare the datasheets for the exact grades you shortlist.
What to freeze before the mold is cut
Short answer: freeze the named grade and glass content, the inspection moisture state, gate placement relative to the pockets, and how the cage is assembled into the bearing.
- The commercial grade, glass content and color, not just “PA66” or “nylon.”
- Pocket geometry, retaining lips and any undercuts that need slides or lifters.
- Whether the cage is a continuous ring, a crown, a segment or a strip, and how it is loaded into the bearing.
- Gate type and position so weld lines sit away from loaded bridges and vestiges sit off working pocket faces.
- Drying and handling of the resin, following the grade datasheet. Polyamides must be processed dry; the supplier sets the window.
- The inspection moisture state, the critical features you will measure, and who approves first-article records. See inspection and approval and drawings and revisions.
If the package later includes metal processing, that work is a separately confirmed responsibility.
What to send with the RFQ
Short answer: send the current drawing and 3D model, the rolling-element geometry, the named PA66 grade, lubricant and temperature notes, and the inspection moisture state.
Align the package with the injection molding RFQ checklist and the bearing cage components hub:
- Drawing revision and 3D model, plus assembly interfaces.
- Rolling-element size, spacing and how the cage is assembled.
- Named material grade, or the constraints you want evaluated, and notes on lubricant, temperature and any aqueous or chemical exposure.
- Critical dimensions and inspection criteria as your specification, including dry-as-molded versus conditioned.
- Sample quantity, expected volume, and whether you need the mold, molded parts, or both (tooling and supply scope).
Numeric tolerance classes or life curves are not invented here. If they exist on your drawing, they remain your acceptance standard. When you are ready, prepare a project brief.
FAQ
Why is PA66 so common for plastic bearing cages?
PA66, with or without glass fiber, is the polymer bearing manufacturers most often injection-mold for cages because it balances strength and elasticity and can form pocket shapes that are hard to stamp in metal. SKF describes it as the most commonly used material for injection-molded cages. Suitability still depends on your temperature, lubricant and life requirement, which only the grade datasheet and your validation can settle.
Should the drawing say PA66 or a glass-filled grade?
Write the named commercial grade and the glass content if any, not a family name alone. Glass fiber raises stiffness and heat capability but makes shrinkage directional and can weaken weld lines on thin pocket bridges. Unfilled PA66 is sometimes chosen when toughness or snap-through assembly matters more. Catalog examples on this site use more than one fill level; they are not a default for every cage.
Should we inspect PA66 cages dry or after conditioning?
Say so on the drawing. Polyamide properties depend on moisture content, which is why ISO 1110 defines an accelerated conditioning method that approximates equilibrium at 23 °C and 50 % relative humidity. Dry-as-molded checks catch process variation early; conditioned checks better reflect size and stiffness after the cage has taken up moisture in service. Many projects record both states for critical pocket and ring dimensions.
When should we look at PPS or POM instead of PA66?
Consider another family when moisture-driven size change is unacceptable, or when the lubricant and temperature would age PA66 too quickly. PPS appears on this site as the design material for a tubular multi-row cage example. POM appears as the catalog example on a slewing-segment page and is often discussed for lower moisture uptake and sliding behavior. Compare datasheets against your lubricant and temperature; do not treat a catalog example as a universal substitute.
Do you guarantee cage life or limiting speed?
No. This page does not offer life, torque or speed ratings. Bearing makers publish their own temperature and lubricant limits for the cages they design; those limits are theirs. For a custom molded cage, operating conditions and validation scope are inputs you define, and inspection methods are agreed for the project against your drawing.
What should we send with a PA66 cage RFQ?
Send the current drawing revision and 3D model, rolling-element size and spacing, the named PA66 or PA66-GF grade, lubricant and temperature notes, and whether dimensions are inspected dry-as-molded, conditioned or both. Include critical features as you specify them, sample versus production quantities, and whether you need the mold, molded parts or both. The injection molding RFQ checklist and the project brief form collect the same inputs.
